Wiremold Ofr Series Overfloor Raceway System Provides Four-Channels Of Capacity and Access to A Wide Range Of Power, Communications, and A/V Connectivity Options In The Smallest, Lowest, Narrowest, Ada Compliant Profile Available In Overfloor Raceway Systems. This System Installs Over Existing Floor Coverings and Is Both Tamper-Resistant and Installer-Friendly, Making It An Ideal Solution For Relocatable or Permanent Installations Where Access Through Floors and Ceilings Is Not An Option.

Wiremold Ofr Series Overfloor Raceway System Provides Four-Channels Of Capacity and Access to A Wide Range Of Power, Communications, and A/V Connectivity Options In The Smallest, Lowest, Narrowest, Ada Compliant Profile Available In Overfloor Raceway Systems. This System Installs Over Existing Floor Coverings and Is Both Tamper-Resistant and Installer-Friendly, Making It An Ideal Solution For Relocatable or Permanent Installations Where Access Through Floors and Ceilings Is Not An Option.

<P>For Branching Ofr Series Raceway At Right Angles. Remove Twistout On Cover to Make A Cross.</P>

<P>Device Plate That Will Accept Up to Four (4) Ports Of Communications Devices. Includes Adapters For Ortronics Tracjack, Series Ii, Pass and Seymour Activate Inserts and Wiremold Open System Communication Modules.</P>

Wiremold Ofr Series Overfloor Raceway System Provides Four-Channels Of Capacity and Access to A Wide Range Of Power, Communications, and A/V Connectivity Options In The Smallest, Lowest, Narrowest, Ada Compliant Profile Available In Overfloor Raceway Systems. This System Installs Over Existing Floor Coverings and Is Both Tamper-Resistant and Installer-Friendly, Making It An Ideal Solution For Relocatable or Permanent Installations Where Access Through Floors and Ceilings Is Not An Option.

<P>For Holding Conductors In Place. Not Ul Listed.</P>

<P>For Right Angle Turns On The Same Surface.</P>

<P>May Be Used As A Cross, Tee or Elbow. Cover Has 1/2'' Trade Size Ko. Base Has 1/2'' and 3/4'' Concentric Trade Size Kos to Enable Connection to Floor Outlet Boxes or Underfloor Duct Systems (Use Chase Nipple Not Included). Two 1500WC Wire Clips Included.</P>

<P>Will Accommodate Commercially Available 15A or 20A Duplex Receptacles. Base Has 1/2'' and 3/4'' Concentric Trade Size Kos. Nonmetallic Cover Has 1500 and 2600 Series Raceway Twistouts On All Four Sides. Two 1500WC Wire Clips Included. Side Wiring Recommended. Gray Finish. Note: Certified to Canadian Safety Standards. For Sale In Canada. When Ordering These Products, Add ''C'' Prefix to Part Number to Denote The Canadian Version, I.E ''C1546B''.</P>

<P>Connects Equipment Grounding Conductor. Provides An Additional Ground For Raceway.</P>

<P>For Covering Joint Where Two Pieces Of 2300BAC Series Raceway Cover Come Together.</P>

<P>For Connecting 2300 Raceway With 1/2'', 3/4'', or 1'' Trade Size Conduit or Armored Cable. 1/2'' and 3/4'' Trade Size Ko On End, 1/2'', 3/4'' and 1'' Trade Size Kos On Bottom.</P>

<P>Divided Fitting to Feed 2300 and 2300 Divided Series Raceway. Includes 1/2'', 3/4'', and 1'' Trade Size Kos On Back and Top.</P>

<P>2300 Series Flat Elbow. For Right Angle Turns On Same Surface.</P>

<P>Use With Any Nonmetallic Round Device Box to Convert Into A Junction Box.</P>

<P>For Hanging Fixtures, Smoke/Fire Alarms and Other Security Devices With 3 1/2'' (89MM) or 4 1/16'' (103MM) Mounting Centers. Has 1/2'' Trade Size Ko. Not For Use With Fans.</P>

<P>One-Gang. Base Has Rectangular Ko. Accepts Industry Standard Faceplates For Switch and Communication Devices. Note: All Boxes Have Combination Twistouts For 400BAC, 800BAC, and 2300BAC On All Four Sides.</P>

<P>For Use With 2300D Series Divided Raceway When Additional Depth Is Required. For Mounting Standard Switches, Receptacles, and Industry Standard Faceplates For Communication Devices.</P>

<P>Divided Two-Gang Box For Use With 2300D Series Divided Raceway. Provides The Ability to Have Both Power and Low Voltage At A Single Point Of Use. Utilizes 5507 Series Faceplates, As Well As Wiremold Open System Communication Modules, Ortronics Tracjack and Series Ii Inserts, and Pass and Seymour Activate Series Inserts. Note: CM-Epla End Plates Are Required When Using Wiremold CM2 Communication Modules and Pass and Seymour Activate Series Inserts. S2-Epl End Plates Are Required When Using Ortronics Seri

<P>Joins Lengths Of 2400B Base Together.</P>